| 1 |
For External Temperature Input code 0 (Fixed Temperature). |
| 2 |
Not applicable for Amplifier Housing code 2. |
| 3 |
Not avialable for Approval Codes code /FS15. |
| 4 |
RTD not provided. |
| 5 |
Preset external temperature value is used for density compensation. |
| 6 |
Tokuchu Approval is required to purchase this option. Contact PMK before quoting. Tokuchu must be approved BEFORE the order is place. |
| 7 |
Applicable for Electrical Connection code 2, 4, 7, and 9. |
| 8 |
Applicable for External Temperature Input code -0, -B, -C, and -D. |
| 9 |
Applicable for External Temperature Input code -0, -1, -2, -3, and -4. |
| 10 |
Applicable for Process Connection code 3, 4, and 5; Installation code 9; Mounting Bracket code N. |
| 11 |
Applicable for Installation code 7. |
| 12 |
This option code includes in Amplifier Housing code 2. |
| 13 |
Consult factory for correct use of this option. Applicable to Measurement Span (Capsule) code M and H. |
| 14 |
Applicable to Output Signal code -E. |
| 15 |
Applicable to Output Signal code -F. |
| 16 |
Order as a separate line item. |
| 17 |
Not applicable with Multi Sensing Measurement Function code A, if not selected with Mass Flow Measurement Function code B, then must have configuration software (see FSA120) |
| 18 |
Percentage of YCA List Price. Warranty only valid within YCA service area. |
| 19 |
Defines the unit of measure used for the MWP on the data plate. If no code is selected, MWP will be expressed in MPa. |
| 20 |
Applicable to Installation code -7 and Wetted Parts Material code S. |
| 21 |
Applicable for Measurement Function code A. |
| 22 |
/A Lightning Protector must be selected. |
| 23 |
For HART protocol type; The change of pressure fluctuation is monitored and then detects the impulse line blockage. Refer to TI 01C25A31-01E for
detailed technical information required for using this function. |
| 24 |
For FOUNDATION Fieldbus protocol type; This option code must be specified with option code EE; The change of pressure fluctuation is monitored and then detects the impulse line blockage. Refer to TI 01C25A31-01E for
detailed technical information required for using this function. |
| 25 |
Limited to 16 Characters Maximum. Must be special ordered if more digits are required. |
| 26 |
General Note for all DPHARP transmitters: Z911 document not available for GS11, GS12, GS16, GU11, GU12, JS4, JS5, J12, PS21,PF23, PF22, NS25, NS21, NS24, NF21, UF1, US1, US24 |
| 27 |
Only available for process connection codes 0 and 5. |
| 28 |
Only Available for process connection codes 1,2, 3, and 4. |
| 29 |
Only A |
| 30 |
Only available for process connection codes 0 or 5. |
| 31 |
Only available for process connection codes 1,2, 3, or 4. |
| 32 |
Only available for opt |
| 33 |
Applicable for process connection codes 0 and 5. |
| 34 |
Applicable for process connection codes 1,2, 3, and 4. |
| 35 |
Applicable for option codes UN and N1. |
| 36 |
Not applicable for plug option code UN. |
| 37 |
Not applicable for option code N1, N2, and N3. |
| 38 |
Programming fee cannot be discounted, it is seen as a document. |
| 39 |
Applicable for Wetted parts material code S. |
| 40 |
See ‘Ordering Information’ in GS. |
| 41 |
Not applicable for electrical connection codes 0, 2, and 4. |
Loading...